38 results found for FAI

• 
• Type

  Technical Bulletin

• Diagnosis of worn wheel end bearings

• May 17

• FAI (38)
• 

...Wheel end bearings SuspensionAxial rods Steering Rack Gaiter KitsStabilizer Link BarsRubber-to-Metal Track control arms General informationWheel end bearingsDrag Links and Centre ArmsTie rod ends V-Torque rodsBall jointRepair kitsTie rod assemblies Expert tipsSteeringWishboneLight Vehicle...

• 
• Type

  Technical Bulletin

• Ford Duratorq Timing Belt Fitting

• Oct 11

• FAI (38)
• 

...Certificate GB00454Technical Bulletin www.faiauto.com Tel: 08708 391802 Best Availability. Best Price.Best Quality. Best Service. LEAF8450The contents of this kit have been assembled as a â...

• 
• Type

  Technical Bulletin

• GM Timing Gears - Essential Fitting Information

• Oct 17

• FAI (38)
• 

...faiauto.comEssential Fitting Information TCK4S/TCK4NGSThe original GM timing gears for this engine up to engine number 19DN0327 were made from sintered material and included a built in spacer/washer. Later engines used pressed steel gears which did not require the spacer/washer. GM have st...

• 
• Type

  Technical Bulletin

• Head Surface Finish

• Apr 18

• FAI (38)
• 

...faiauto.com Before fitting a replacement head gasket Head Surface Finish Ensure the cylinder head and engine block surfaces have been checked, ensuring level sealing surfaces.Maximum values: Roughness...

• 
• Type

  Technical Bulletin

• Hyundai, Kia, Mitsubishi 2.5 TD - Oil Pump Variations

• Jun 17

• FAI (38)
• 

...faiauto.com Choosing the correct oil pump Hyundai/Kia/Mitsubishi 2.5 TD EnginesOP342OP271OP270 OP264Raised Bolt Fixing Machined Flat Fixing Raised Bolt Fixing Raised Bolt Fixing HYUNDAI - 2134042800Engines: 4D56T/4D56TD MITSUBISHI - MD181583Engines: 4D56T/4D56TDMITSUBISHI - MD364254Engin...

• 
• Type

  Technical Bulletin

• Installation of PTFE Oil Seals

• Mar 17

• FAI (38)
• 

...faiauto.comInstallation informationPTFE Oil SealsImportant :• Ensure contact surfaces are clean, dry and damage free.• Carefully push seal into position, without damaging the PTFE material.• When fitted, do not start engine for a minimum of 4 hours.Važno:• Postarajte se da je kont...

• 
• Type

  Technical Bulletin

• Link Rod Tightening Advice

• Nov 10

• FAI (38)
• 

...LINK ROD TIGHTENING ADVICE FA I recommend that an airgun should not be used to tighten the nuts on a link rod. Using an airgun increases the risk of .........• Over - tightening• Snapped ball pin• Cross threading - shearing thread FA I recommend that only a suitable manual tool s...

• 
• Type

  Technical Bulletin

• Mitsubishi 4D56T 16V Engine Head Gasket Modification

• Jan 17

• FAI (38)
• 

...faiauto.comHG2101 uses latest OE modification.Mitsubishi 4D56T 16V Engines Following OE modification, FAI now offers the latest design head gasket for Mitsubishi 4D56T 16V engines. The new design has a corrugated upper surface and smooth profile lower layer, completely matching OE. This g...

• 
• Type

  Technical Bulletin

• Mitsubishi 4M4 Head Gaskets

• Jul 18

• FAI (38)
• 

...faiauto.comHG1539 vs. HG2258Mitsubishi 4M4# Head Gaskets Similarity in gaskets can easily lead to fitment and performance issues. The two gaskets below are a case in point, both fit Mitsubishi four cylinder common rail 4M4# generation engines. However HG1539 fits the earlier 3.2 (4M41) eng...

• 
• Type

  Technical Bulletin

• Multi-Layered (Laminated) Steel Head Gaskets Installation

• Jul 17

• FAI (38)
• 

...faiauto.com Before fitting this replacement head gasket Multi-Layered (Laminated) Steel Head Gaskets Ensure the cylinder head and engine block surfaces have been checked, ensuring level sealing surfaces.Maximum values: Roughness...