124 results found for LuK

• 
• Type

  Technical Bulletin

• Clutch grabs when shunting

• Dec 14

• LuK (131) Contact
• 

...Setting the clutch booster is only necessary if either the clutch pressure plate, clutch disc or piston rod has been replaced. A suitable diagnostic device is required for working on or adjusting the transmission control.Clutch grabs when shunting Manufacturer: Mercedes-BenzModels: Actr...

• 
• Type

  Technical Bulletin

• Mercedes Actros Grabbing clutch

• Dec 14

• LuK (131) Contact
• 

...Grabbing clutch Possibly caused by incorrect adjustment of the clutch boosterFabricante: Mercedes-BenzModelos: Actros MP 2 (2003 -2008) Actros MP 3 (2008 - )Tipo: 932, 933, 934 with code (GE2) EDC II (Electronic Drive Control) 930, 932, 933, 934, 940, 944 with code GE3 Mer...

• 
• Type

  Technical Bulletin

• How to grease clutch hubs

• May 15

• LuK (131) Contact
• 

...How to grease clutch hubs Proper use of lubricantsFigure 1: Greasing the hub splinesThe clutch uses the clutch disc to transfer the engine torque to the transmission. The coefficient of friction is one of the most important properties here. Even extremely small quantities of grease or...

• 
• Type

  Technical Bulletin

• LuK RepSet with modified clutch disc

• Jul 15

• LuK (131) Contact
• 

...LuK RepSet with modified clutch disc Manufacturer: BMW LuK RepSet: 624 3530 00 624 3535 00 624 3540 00Fig. 1: Clutch disc of the LuK RepSet (diameter 228mm)For improved driving comfort, the clutch discs for various models of the motor vehicle manufacturer listed above have been modifie...

• 
• Type

  Technical Bulletin

• Misalignment of diaphragm spring fingers

• Jul 15

• LuK (131) Contact
• 

...Misalignment of diaphragm spring fingersManufacturers: PSA/Peugeot, Citroën LuK RepSet: 623 3325 00 623 3325 09 623 3325 33 601 0021 00Fig. 1: Misalignment of diaphragm spring fingers on a dismantled clutchThe diaphragm spring fingers of the pressure plate in the LuK RepSet are m...

• 
• Type

  Technical Bulletin

• Removal of pull-type clutches

• Jul 15

• LuK (131) Contact
• 

...Note:Separating the transmission from the engine without removing the release fork pivot pin first can damage the release bearing system and the clutch!Removal of pull-type clutches Special tool requiredManufacturers: Citroën Fiat PeugeotFigure 1: Klann special tool KL-1600-10 enable...

• 
• Type

  Technical Bulletin

• Clutch hub coatings - Lubricants are not always necessary

• Nov 15

• LuK (131) Contact
• 

...Fig. 1: Nickelled hubs must not be greasedFig. 2: Phosphated hubs must be greasedClutch hubs can have different types of coatings. For this reason, when working on the clutch the following points must be obser ved: • Nickelled hub splines (Fig. 1), characterised by their matte silver col...

• 
• Type

  Technical Bulletin

• Use of lubricants with release bearings

• Aug 17

• LuK (131) Contact
• 

...Installation notice Use of lubricants with release bearingsThree different types of bearing housing are used in the release bearings of the current product range. Different methods must be used when performing maintenance and repair work on them. Technicians should obser ve the followin...

• 
• Type

  Technical Bulletin

• LuK RepSet 620 3115 00 Installation notice

• Aug 17

• LuK (131) Contact
• 

...LuK RepSet 620 3115 00 Installation notice Note:For repair and maintenance work on clutches, Schaeffler Automotive Aftermarket always recommends use of special tool Part. No.: 400 0237 10. Instructions explaining how to use the tool are available at www.repxpert.uk.Installation notice...

• 
• Type

  Technical Bulletin

• LuK clutch discs may be smaller than OE

• Aug 17

• LuK (131) Contact
• 

...LuK clutch discs Smaller diameter than original equipmentVehicles have to be as light as possible in order to meet increasingly strict CO2 emission limits. That's why engineers and scientists are constantly working to create lighter materials and innovative manufacturing methods. Their fin...